This weekend, I received my ACME Arietta G25 Atmel ARM board, and tried to get it going with my Mac. I ordered the “plain” version with 128 MB RAM, as well as one with 256MB RAM, as well as Wifi boards and the DPI debug board.
After soldering in the necessary posts, I attached the DPI board and verified that my Mac has the right FT232 driver to access the console, no problems here.
I then fired up by Ubuntu VirtualBox machine and followed the instructions to build the Micro-SD-Card image. I then proceeded to boot successfully from the card.
Through the console, I could get the Wifi card going; since I wanted to have support for more than a single network, I extended the configuration through wpa_supplicant.conf.
ACME has configured a Gadget driver to supply an Ethernet interface through the host port on the Arietta; in ACMEs configuration, this is set to offer both RNDIS and CDC EEM modes. Unfortunately, Mac OS X 10.9 doesn’t support either.
After some more reading, I decided to build my own kernel and modules. To get a Mac-compatible setup for the USB Gadget driver, run menuconfig, and navigate to
- Device Drivers
- USB support
- USB Gadget Support (at the very bottom of the list)
For Mac compatibility, de-select the RNDIS support and the Ethernet Emulation Model (EEM) support under Ethernet Gadget.
I also chose to enable the Serial Gadget and the CDC Composite De
vice (Ethernet and ACM).
After building the kernel and replacing the files on the SD Card, I changed the module load line in /etc/network/interfaces to load the g_cdc module instead of the g_ether module, and added an entry in /etc/inittab for /dev/ttyGS0 to also have a console through the host port.
Hi thanks for your usefully post. I try to compile at91boot and arietta kernel directly on my macbook without passing from an ubuntu virtual machine. But even if compile myself an arm toolchain I have some error when compile at91bootloader (ld symbols not found on x83_64)… do you know if there is a simple way to compile all of this directly on a macbook?
Thanks
Samuele
I’ve decided to go with a Linux VM for two reasons: there’s enough cookbooks and examples on how to build these kinds of images on Linux. That way, you can follow the instructions exactly, and if anything doesn’t work, there’s a decent chance you find someone who has solved that problem before. Secondly, getting the build toolchain to work on Mac OS X probably is possible, but since so few people do that, and there’s lots and lots of arcane details you have to get right, it’s really hard.
My ultimate goal is to get FreeBSD running on the Arietta, and I do have a powerful FreeBSD server I can use for cross-building both FreeBSD and packages; I don’t think I’ll try and set up a toolchain on the Mac anytime soon.
Hi thanks to you post, I’ve successfully build a mac-compatibile kernel. I’ve some problems to share the Internet connection between Arietta and the mac via g_cdc. I can ping Arietta from mac and viceversa by when I try the apt-get update I can’t reach the repositories. Are you able to share Internet connection?
Bye
Samuele
Have you tried Internet Sharing? http://support.apple.com/kb/PH13855?viewlocale=en_US&locale=en_US
The Mac will run the virtual CDC Ethernet like a router, and provide IP addresses via DHCP, so you probably want to reconfigure the network settings on the Arietta.
I also got the Wifi board for the Arietta, and that’s how I’ve been installing packages.
Yes I tray the internet sharing bit without success…now I’waiting for the WiFi antenna because i’ve bought the WiFi board that require the external antenna but I miss the antenna 🙂
Hhm, I tried using Internet Sharing, but it’s not working for me either. The quick solution might be to install tinyproxy on your Mac, and point apt at that.
I also got the Wifi modules that require an antenna, but I can use them even without an antenna; I’m about 15 feet and two brick walls from my wifi router, for what it’s worth.
Wow fantastic!! I configured successfully tiny proxy on my Mac and now I can access apt repos from arietta!
Regarding the WiFi connection I’m investigating was wrong… like also I don’t understand why the usage of Mac Internet Sharing doesn’t works…
Bye!
Hi! I have found the problem on connecting arietta via wifi… an error on a key. Now I have the connection available on wireless without antenna 🙂
Hello,
I compiled the kernel, installed it on the SD card but once Arietta connected on the MAC, i can’t ping it
In the network settings of the mac i have a “CDC Composite Gadget” entry that is created with DHCP as a default value. I activated the Internet Sharing with a bridge between my wifi and the CDC entry.
Then if i do the ping to 192.168.10.10 i can’t get an answer. The IP address is set to a 169.254.x.x which i can ping but get a connection refused for the SSH command.
I tried to force all values on the network connection but same result …
Any advice why i can’t get it ?
Thanks a lot for this write up! Just successfully connected to my ariettta board 😉
Hello, I am moving my code from a raspberry pi to the arietta. I just got one, but have no idea what to do next after I get the sd card loaded. Does anybody have or know about how to access linux??
An excellent read that will keep readers – particularly me – coming back for more! Also, I’d genuinely appreciate if you check my website Webemail24 about Martial Arts. Thank you and best of luck!
You’ve written terrific content on this topic, which goes to show how knowledgable you are on this subject. I happen to cover about Search Engine Optimization on my personal blog Seoranko and would appreciate some feedback. Thank you and keep posting good stuff!
My site ArticleHome covers a lot of topics about Website Traffic and I thought we could greatly benefit from each other. Awesome posts by the way!
Nice post! You have written useful and practical information. Take a look at my web blog Autoprofi I’m sure you’ll find supplementry information about Car Purchase you can gain new insights from.
Having read your posts. I believed you have given your readers valuable information. Feel free to visit my website Articlecity and I hope you get additional insights about Website Design as I did upon stumbling across your site.
The way you put together the information on your posts is commendable. I would highly recommend this site. You might also want to check my page Articleworld for some noteworthy inputs about Perfumes.
The way you put together the information on your posts is commendable. I would highly recommend this site. You might also want to check my page Article Sphere for some noteworthy inputs about SEO.
Superb layout and design, but most of all, concise and helpful information. Great job, site admin. Take a look at my website Article Star for some cool facts about Website Design.
An interesting topic and I’m glad to come across your page where I found some helpful insights. Check out my website 46N too, if you need additional resources about Thai-Massage.
This was a delight to read. You show an impressive grasp on this subject! I specialize about Internet Marketing and you can see my posts here at my blog YW9 Keep up the incredible work!